How To Make A Sausage Dog Draft Excluder?

An easy to follow tutorial for creating a cute wind blocker out of an old pair of pantyhose and a little bit of creativity

Using this technique, you can make a sausage dog out of an old pair of tights. Children of any age can attempt to make it because it is simple to make, requiring little sewing, especially if the eyes and ears are glued on. For the ears, we used old mittens, although kids’ socks might also work. Use it to block drafts or just cuddle up with your lovable dog!

worn-out woolen tights Wool fabric scraps dual buttons Thread and a needle Stuffing or clean, old socks shabby mittens Scissors

1. Use a pair of scissors to cut one of the tights’ legs off an old pair as high as you can.

2. Stuff the cut-off leg of the tights with stuffing or other material until it resembles a sausage. At the very end, leave a little space empty.

3. Cut a length of wool, wrap it tightly around the sausage’s end, and secure it with a double knot.

4. To create a large doggy nose, knot another piece of wool around the toe at the opposite end. To keep the shape in place, tie a knot once more.

5. To create the dog’s ears, sew an old glove onto each side of the sausage slightly above the nose.

6. Cut some hearts from leftover fabric using a heart-shaped template.

7. Using a needle and wool, sew the hearts on the sausage. Put a knot in the wool’s end, and then sew through the tights. Stitch back through the tights after pushing the needle up from the back of the heart to the front near the edge. After going all the way around each heart, tie a knot.

8. To create eyes for the sausage, sew buttons onto it. To make the dog’s collar, cut a strip of fabric or use a piece of ribbon, and tie it around the animal’s neck.

Make a cozy draft excluder on your own.

You want your house to feel cozy in the winter. But turning up the thermostat to the max is neither the most economical nor environmentally friendly method to remain warm. Keeping the heat where you want it can be made much easier by stopping draughts from leaky doors.

But why not make your own draught excluder if you don’t happen to have a Napoleon cat or a sausage dog on hand? You can make one specifically for the holiday season for your house or as a lovely homemade gift for family or friends because they are so simple to make.

How is a sausage draft excluder made?

There are several additional techniques for creating a DIY draught excluder. Old garments can even be recycled.

Cut the leg off an old pair of trousers or the arm off an old sweater to make a fast version of draught excluders. Fill them, then sew the ends together.

Have any worn-out socks or tights? These could be stuffed with stuffing. Do not forget to add something to weigh them down and secure them. Before stitching them together, include some dry beans or peas with the filler.

What filler works best for a draft excluder?

Beginners and more seasoned sewers alike may benefit from DIY home projects because they can frequently be completed quickly, with readily available supplies, and for practical purposes. What are the best fillings for draught excluders is one thing you would want to know.

The ideal fillings for draught excluders are those that condense the space to stop airflow. These include sand, cotton or polyester wadding, and worn-out clothing.

How do you create a door draft blocker without sewing?

Amazing no-sew draft stoppers can be made from knee socks or the shorter leg of a pair of tights. Cut out the foot portion if you don’t want it to appear as though someone is leaning against your door. Tie the ends together rather than sew them. It has a fantastic handmade, rustic style. Many designs recommend filling with wheat, rice, or buckwheat, but if you’re worried about pests or triggering someone’s allergies, consider using kitty litter or beads instead. Just make sure to get off your feet before doing so!

What is contained in a draft excluder?

To close the opening at the threshold, a door draught excluder is positioned at the bottom of the door. These draught excluders were traditionally composed of cloth and sawdust and fashioned like sausages during the Victorian era.

In Australia, draught excluders made of fabric tubes filled with sand are known as “door snakes.”

They were utilized by the Outback hotel where they stayed while filming Walkabout, according to Jenny Agutter, to keep poisonous snakes out of the visitors’ rooms.

What size Draught Excluder should it have?

  • Make sure you have a piece of cloth between 35 and 40 cm wide that is just slightly longer than the door frame where you plan to hang your finished draft excluder. This material can be a scrap from a different project or an old garment that you no longer require.
  • Make sure the side of the cloth you want to reveal is on the inside as you fold it in half lengthwise.
  • To ensure the fabric stays in place for the following step, pin along the length of the cloth and along one end to create an open tube. Use a tape measure to pin the cloth in a straight line if you haven’t quite cut a rectangle, and then cut off the extra fabric afterward.
  • Remove the pins as you go and sew the pinned sides, either by hand or with a sewing machine. Hold the fabric in place while you remove the pins to keep it straight. To make them look neat when they are turned inside out, sew as closely into the corners as you can.
  • Turn the open tube inside out so that the side of the fabric you want to be seen is now on the outside after completing step four. You might wish to press the seams now, depending on the sort of fabric you’re using.
  • Fill the tube with the stuffing of your choice. If you’re using used tights, shred them beforehand to prevent lumps in your finished draught excluder.
  • When your tube is full, carefully and neatly hand stitch the end closed.
  • Now that your draught excluder is completely operational, you might want to add some finishing touches. Although ribbons, buttons, and pom poms also look fantastic, you could easily cut and make your own felt letters.

How can a draft on a door be stopped?

The most crucial step in winterizing a house is forgetting to lock the windows. As the sashes are pulled together by window locks, the air leak is sealed.

  • If your windows are large, you might want to install two locks, rather than just one in the center, to shut the gap completely across the sash.
  • Pull down the top sash of your double-hung windows and install some weatherstripping along the top edge before locking the doors.
  • Then, before locking, tighten the sash as far as you can.

Which side of the door should a draught excluder be installed on?

Most DIY stores carry draught excluders, which resemble long brushes that span the width of the bottom of the door. When the door is opened and closed, this brush fills the space between the door and the floor and moves along the floor.

You’ll need the following before attaching the door excluder:

  • Measurement tape
  • a marker
  • Hacksaw
  • Pliers
  • Screwdriver

When you have all of these, you can start installing the draught excluder on your door:

  • Start by taking a measurement of your door’s width. Take the measurement directly at the bottom of the door since this is where the draught excluder needs to be installed.
  • The brush will be kept inside of an attachable seal. Before removing the brush, measure the area and use the marker pen to mark it on the brush seal.
  • You can now use the hacksaw to reduce the seal’s width to match your door after removing the brush from it (you should take precautions at this stage by wearing gloves and protective eyewear).
  • Before removing the brush once more, reinstall it in the seal and make a notation where the surplus brush protrudes from the seal.
  • You must now reduce the size of the brush as well; instead of using the saw for this task, use the pliers.
  • Make sure the brush on the majority of draught excluders is in contact with the floor before sticking it to the door.
  • You can screw nails into the door using the screw holes in the seal.

For more specific instructions on how to install a draught excluder on a door, refer to the instructions that will be included with your draught excluder.

Do draft excluders merit the cost?

Draught excluders have long been used as a standard practice during the cooler winter months to prevent chilly air from entering homes. They used to just be an old blanket or piece of fabric wrapped up into a tube and placed at the bottom of front doors, rear doors, and other exterior doors to keep the wind out many years ago.

The technology behind draught excluders has advanced significantly over the years, and many new double glazing units and doors come totally sealed with draught excluders built in as standard. Older front doors, back doors, exterior doors, and even stable doors can easily be fitted with do-it-yourself draught excluders. These devices typically consist of a straightforward length of aluminum (the carrier), to which a flexible silicone or rubber strip is attached to close the gap at the bottom of the door or window. Additionally, there are a variety of flexible draught excluders available in rolls that can be used to seal around the frames of exterior doors and windows to prevent draughts from entering. These products are often made of encased foam.

Although it’s important to have some natural ventilation—in fact, The Energy Saving Trust advises that the air in your home should change naturally at a rate of 0.5 to 1.0 times per hour—many older homes have external doors and windows that are warped or improperly fitted, which can increase energy consumption and result in wasted money on fuel bills because of heat loss.

Draughts may be prevented, which improves the comfort of your house while also costing less. It has been demonstrated that adding a draught excluder to windows, back doors, or front doors can minimize heat loss by up to 30% in extreme circumstances and typically results in savings of 10% to 20%. In terms of installation costs and potential savings, draught excluders are one of the most popular and effective steps you can take to lower your home’s energy costs during the cold weather.

Draught excluder should be applied to the door or the frame.

Draughts can enter the room in a number of places besides the bottom of the door. To prevent cold air from entering your home and heat from escaping, the borders and top should also be well sealed. Install rubber, foam, brush, or wiper strips to reduce draughts coming through doors. Depending on the product, these may also be fastened to the frame using screws or nails in addition to adhesive.

‘Look into using self-adhesive edging strips to close up any gaps that are present around the border of the door. To ensure the edging adheres properly, remember to clean the surface first, advises Jill McLintock.

Draught seals are offered in a variety of hues to complement the style and color of your door. To purchase the proper type, quantity, and size of excluder, be sure to measure the length, breadth, and depth of the gap that needs to be sealed in your door. The majority of products come with fasteners, but always be sure.

On the supplier’s website, these kinds of weatherstrip edging will be prominently labeled when they also function as an acoustic seal. If your home is near a busy street and you want to reduce both draughts and unpleasant outside noises, this can be a perfect alternative.